收藏本站
ZXLD1320
Device description
The ZXLD1320 is a buck mode inductive DC-DC converter, with an internal switch, designed for
driving single or multiple LEDs in series up to a total of 1.5A output current. Depending upon
supply voltage (VIN), LED forward voltage drop (V LED ) and circuit configuration, this can provide
up to 24W of output power.
Applications cover both commercial and automotive environments with VIN ranging from 4 to 18V.
?
The device employs a modified Pulse Frequency Modulation (PFM) control scheme, with
variable "ON" and "OFF" time control and adjustable peak switch current limiting.
General device operation (refer to block diagram)
Normal operation
Control is achieved by sensing the LED current in a series resistor (R M ), connected between the
two inputs of the LED Current Monitor. This generates a proportional current (IMON) that charges
the external integrator capacitor C FB . I MON is balanced against a reference discharge current
(I ADJ ) generated at the output of a second voltage to current converter driven from the demand
voltage (V ADJ ) on the ADJ pin. The difference between I MON and I ADJ is integrated by C FB to
produce an error voltage. A comparator takes a summed version of the voltage at the ISENSE pin
and a fraction of this CFB voltage and resets the latch driving the switch when the sum is greater
than 50mV. The switch transistor is turned on by the output of the SR latch, which remains set
until the emitter current in the switch transistor produces a voltage drop Vsense (=50mV nominal)
in external resistor Rsense, defining a preset maximum switch current of 50mV/Rsense.
Operation is such that a rising error voltage on CFB will effectively lower the voltage required on
the ISENSE pin and therefore reset the latch earlier in the switching cycle. This will reduce the
'ON' time of the switch and reduce the peak current in the switch from its preset maximum value.
Similarly, a falling error voltage will reset the latch later and the peak switch current will be
increased. The control loop therefore reduces or increases the energy stored in the coil during
each switching cycle, as necessary, to force the LED current to the set value. This results in high
accuracy, as no error is needed in the LED current to drive the servo to the required region.
The time taken for the coil current to reach the peak value depends on several factors: the supply
voltage, the peak coil current required at that particular LED power and whether the system
operates in "continuous" or "discontinuous" mode. The time allowed for the coil current to
discharge into the LED is fixed by the 'Variable Off Delay' monostable, whose period is modified
by the power demand signal on the ADJ pin. This monostable determines the time for which the
latch remains reset (switch off) and provides a longer "OFF" period at lower power settings,
helping to keep the parameters within an acceptable range.
Note that the "ON" period and the "OFF" period are set by the supply voltage, LED power and
external components chosen. The frequency is therefore determined by these parameters and is
NOT fixed. The 500mV reference voltage defines the nominal VADJ voltage and this defines the
100% output current. For lower LED currents, the ADJ pin can be-driven from an external dc
voltage (50mV<VADJ<500mV) or a low frequency Pulse Width Modulated (PWM) waveform.
Issue 1 - January 2008
? Zetex Semiconductors plc 2008
9
www.zetex.com
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ZXLD1321DCATC IC LED DRVR WHITE BCKLGT 14-TDFN
ZXLD1322DCCTC IC LED DRIVR WHITE BCKLGT 14-DFN
ZXLD1350ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD1352ET5TA IC LED DRIVER HIGH BRIGHT TSOT-5
ZXLD1356DACTC IC LED DRIVER WHITE BCKLGT 6-DFN
ZXLD1360ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD1362ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD1366DACTC IC LED DRIVER WHITE BCKLGT 6-DFN
相关代理商/技术参数
ZXLD1321 制造商:ZETEX 制造商全称:ZETEX 功能描述:Boost mode DC-DC converter for LED driving with 1A output and current control
ZXLD1321DCATC 功能描述:直流/直流开关转换器 DC-DC Boost Conv 1A output RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
ZXLD1322 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:BUCK/BOOST MODE DC-DC CONVERTER
ZXLD1322DCCTC 功能描述:直流/直流开关转换器 Buck-Boost DC-DC Con 0.7A output RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
ZXLD1322DCCTC-CUT TAPE 制造商:DIODES 功能描述:ZXLD1322 Series 15 V 600 kHz 700 mA Buck/Boost Mode DC-DC Converter - DFN-14
ZXLD1322DCTC 制造商:ZETEX 制造商全称:ZETEX 功能描述:Buck/boost mode DC-DC converter for LED driving with 700mA output and current control
ZXLD1350 制造商:ZETEX 制造商全称:ZETEX 功能描述:350mA LED driver with internal switch
ZXLD1350_07 制造商:ZETEX 制造商全称:ZETEX 功能描述:350mA LED driver with internal switch